The Art of Plumbing Fundamentals When You Install a Bathtub
The Art of Plumbing Fundamentals When You Install a Bathtub
Blog Article
Just how do you actually feel with regards to How to Install a Bathtub Yourself?
Setting up a bath tub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily accessible, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to move out the old tub and also set in the brand-new one. Ensure you have actually certified on your own for the job and also fit trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is far better to take into consideration using one before you begin. Chances are you might require a professional plumber to make tube links.
This short article will help you set up a new bathtub in your shower room if you have already bought a brand-new tub as well as don't require to alter the plan of your previous water supply pipes.
Your tools and also material list ought to consist of the following:
Getting ready for the Installation
First of all, the supporting frame provided with the bath must be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to stop stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the limited access that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before going on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, put the tub in the called for position. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Turn on the water supply and check all joints and brand-new pipework for leaks as well as tighten them if needed. Fill the bathtub as well as additionally inspect the overflow outlet and the typical outlet for leakages.
Ultimately, fix the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the bath tub ought to wait until the bath tub has been made use of a minimum of when as this will settle it right into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in place in between the faucet and also the sink. Protect the tap in place with the maker provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind ought to be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bath and the tiling, resulting in complications with wetness and also possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and also fittings. They are marketed in tubes and also cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very interested in Tools You Need to Install a New Bathtub and I am hoping you enjoyed reading our article. Do you know anybody else who is curious about the subject? Be sure share it. I treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.
Diverse plumbing issues? We resolve. Report this page